CCNA 2 RSE v5.0 Chapter 6 Skill Assessment – Packet Tracer

CCNA 2 RSE v5.0 Chapter 6 Skill Assessment – Packet Tracer 2014 Routing and Switching Essentials RSE Chapter 6 SIC Practice Skills Assessment – Packet Tracer A few things to keep in mind while completing this activity: 1. Do not use the browser Back button or close or reload any exam windows during the exam. […]

Practice CCNA 2 v5 Exam Packet Tracer

CCNA 2 RSE Practice Skills Assessment – PT CCNA Routing and Switching Routing and Switching Essentials Practice Skills Assessment – Packet Tracer A few things to keep in mind while completing this activity: Do not use the browser Back button or close or reload any exam windows during the exam. Do not close Packet Tracer when […]

CCNA 2 R&S Essentials Practice Final v5.0 2014 exam answers

CCNA 2 R&S Essentials Practice Final v5.0 2014 exam answers   1 Which command would be best to use on an unused switch port if a company adheres to the best practices as recommended by Cisco? switchport port-security mac-address sticky ip dhcp snooping switchport port-security mac-address sticky mac-address switchport port-security violation shutdown shutdown* 2 Refer to […]

CCNA 2 R&S: Routing and Switching Essentials Final Exam Answers

CCNA 2 v5.0 R&S Essentials Final Exam 2014 1. What are two features of a link-state routing protocol? (Choose two.) The database information for each router is obtained from the same source. Routers send triggered updates in response to a change. Routers create a topology of the network by using information from other routers. Paths are chosen […]

CCNA 2 Chapter 11 v5.0 Exam Answers 2014

CCNA 2 Chapter 11 v5.0 Exam Answers 2014 1 Which version of NAT allows many hosts inside a private network to simultaneously use a single inside global address for connecting to the Internet? dynamic NAT port forwarding PAT* static NAT 2 What is the group of public IPv4 addresses used on a NAT-enabled router known […]

CCNA 2 Chapter 10 v5.0 Exam Answers 2014

CCNA 2 Chapter 10 v5.0 Exam Answers 2014   1 Refer to the exhibit. What should be done to allow PC-A to receive an IPv6 address from the DHCPv6 server? Add the IPv6 address 2001:DB8:1234:5678::10/64 to the interface configuration of the DHCPv6 server. Configure the ipv6 nd managed-config-flag command on interface Fa0/1. Change the ipv6 […]

CCNA 2 Chapter 9 v5.0 Exam Answers 2014

CCNA 2 Chapter 9 v5.0 Exam Answers 2014 1 A network administrator needs to configure a standard ACL so that only the workstation of the administrator with the IP address 192.168.15.23 can access the virtual terminal of the main router. Which two configuration commands can achieve the task? (Choose two.) Router1(config)# access-list 10 permit 192.168.15.23 […]

CCNA 2 Chapter 8 v5.0 Exam Answers 2014

CCNA 2 Chapter 8 v5.0 Exam Answers 2014 1 Which OSPF component is identical in all routers in an OSPF area after convergence? routing table link-state database* SPF tree adjacency database 2 Which three statements describe features of the OSPF topology table? (Choose three.) When converged, all routers in an area have identical topology tables.* […]

CCNA 2 Chapter 7 v5.0 Exam Answers 2014

CCNA 2 Chapter 7 v5.0 Exam Answers 2014 1 What is the purpose of the passive-interface command? allows interfaces to share IP addresses allows an interface to remain up without receiving keepalives allows a router to send routing updates on an interface but not receive updates via that innterface allows a routing protocol to forward […]