CCNA 2 Chapter 11 v5.0 Exam Answers 2014

CCNA 2 Chapter 11 v5.0 Exam Answers 2014 1 Which version of NAT allows many hosts inside a private network to simultaneously use a single inside global address for connecting to the Internet? dynamic NAT port forwarding PAT* static NAT 2 What is the group of public IPv4 addresses used on a NAT-enabled router known […]

CCNA 2 Chapter 10 v5.0 Exam Answers 2014

CCNA 2 Chapter 10 v5.0 Exam Answers 2014   1 Refer to the exhibit. What should be done to allow PC-A to receive an IPv6 address from the DHCPv6 server? Add the IPv6 address 2001:DB8:1234:5678::10/64 to the interface configuration of the DHCPv6 server. Configure the ipv6 nd managed-config-flag command on interface Fa0/1. Change the ipv6 […]

CCNA 2 Chapter 9 v5.0 Exam Answers 2014

CCNA 2 Chapter 9 v5.0 Exam Answers 2014 1 A network administrator needs to configure a standard ACL so that only the workstation of the administrator with the IP address 192.168.15.23 can access the virtual terminal of the main router. Which two configuration commands can achieve the task? (Choose two.) Router1(config)# access-list 10 permit 192.168.15.23 […]

CCNA 2 Chapter 8 v5.0 Exam Answers 2014

CCNA 2 Chapter 8 v5.0 Exam Answers 2014 1 Which OSPF component is identical in all routers in an OSPF area after convergence? routing table link-state database* SPF tree adjacency database 2 Which three statements describe features of the OSPF topology table? (Choose three.) When converged, all routers in an area have identical topology tables.* […]

CCNA 2 Chapter 7 v5.0 Exam Answers 2014

CCNA 2 Chapter 7 v5.0 Exam Answers 2014 1 What is the purpose of the passive-interface command? allows interfaces to share IP addresses allows an interface to remain up without receiving keepalives allows a router to send routing updates on an interface but not receive updates via that innterface allows a routing protocol to forward […]

CCNA 2 Chapter 6 v5.0 Exam Answers 2014

CCNA 2 Chapter 6 v5.0 Exam Answers 2014 1 What are two advantages of static routing over dynamic routing? (Choose two.) Static routing is more secure because it does not advertise over the network.* Static routing is relatively easy to configure for large networks. Static routing requires very little knowledge of the network for correct […]

CCNA 2 Chapter 5 v5.0 Exam Answers 2014

CCNA 2 Chapter 5 v5.0 Exam Answers 2014 1 Fill in the blank. Do not use abbreviations. A network engineer is troubleshooting the configuration of new VLANs on a network. ​Which command is used to display the list of VLANs that exists on the switch? ” show vlan ” 2 What is a disadvantage of […]

CCNA 2 Chapter 4 v5.0 Exam Answers 2014

CCNA 2 Chapter 4 v5.0 Exam Answers 2014 1 What type of IPv6 address is required as a minimum on IPv6 enabled interfaces? static global unicast link-local* loopback unique local 2 In order for packets to be sent to a remote destination, what three pieces of information must be configured on a host? (Choose three.) […]

CCNA 2 Chapter 3 v5.0 Exam Answers 2014

CCNA 2 Chapter 3 v5.0 Exam Answers 2014 1 A network administrator is determining the best placement of VLAN trunk links. Which two types of point-to-point connections utilize VLAN trunking?​ (Choose two.) between two switches that share a common VLAN between a switch and a server that has an 802.1Q NIC* between a switch and […]

CCNA 2 Chapter 2 v5.0 Exam Answers 2014

CCNA 2 Chapter 2 v5.0 Exam Answers 2014 1 Which type of cable does a network administrator need to connect a PC to a switch to recover it after the Cisco IOS software fails to load? a coaxial cable a crossover cable a straight-through cable a console cable* 2 Which two basic functions are performed […]