Cisacad.net

Examenes Cisco CCNA v7.0 y IT Essentials v8 en Español
Menu
  • Inicio
  • CCNA v7.02
    • CCNA 1 v7.02
    • CCNA 2 v7.02
    • CCNA 3 v7.02
  • CCNA v6.0
    • CCNA 1 v6.0
    • CCNA 2 v6.0
    • CCNA 3 v6.0
    • CCNA 4 v6.0
  • CCNA v5.0
    • Exámenes Cisco CCNA 1 v.5.0
    • Exámenes Cisco CCNA 2 v.5.0
    • Exámenes Cisco CCNA 3 v.5.0
    • Exámenes Cisco CCNA 4 v.5.0
  • Security
    • Network Security v1.0
    • CCNA Security 2.0
  • It-essentials v7.01
  • Ciberseguridad
    • Introducción a la Ciberseguridad v2.1
    • Cybersecurity Essentials v1.1
  • Mas Cursos
    • Introduccion a IoT v2.0
    • GetConnected
    • Networking Essentials v2
    • Entrepreneurship

CCNA1 v5 Introduction to Networks Practice Final – CLI command answers

CCNA1 v5 Introduction to Networks Final – CLI command answers

You will practice and be assessed on the following skills:

  • Configuration of initial IOS device settings
  • Design and calculation of IPv4 addressing
  • Configuration of IOS device interfaces including IPv4 and IPv6 addressing when appropriate
  • Addressing of network hosts with IPv4 and IPv6 addresses
  • Enhancing device security, including configuration of the secure transport protocol for remote device configuration
  • Configuration of a switch management interface

Requirements by device:

  • Town Hall router:
  • Configuration of initial router settings
  • Interface configuration and IPv4 and IPv6 addressing
  • Device security enhancement or “device hardening”
  • Secure transport for remote configuration connections as covered in the labs.
  • Backup of the configuration file to a TFTP server
  • Administration Switch:
  • Enabling basic remote management by Telnet
  • PC and Server hosts:
  • IPv4 full addressing
  • IPv6 addressing

ccna1 skill final

Device Interface IPv4 Address Subnet Mask IPv4 Default Gateway IPv6 Address IPv6 Default Gateway
Town Hall G0/0 N/A 2001:DB8:ACAD:A::1/64 N/A
G0/1 N/A 2001:DB8:ACAD:B::1/64 N/A
Administration Switch Vlan 1 N/A N/A
Reception Host NIC 2001:DB8:ACAD:A::FF
Operator Host NIC 2001:DB8:ACAD:A::15
IT Host NIC 2001:DB8:ACAD:B::FF
TFTP Server NIC 2001:DB8:ACAD:B::15

Step 1:

Design an IPv4 addressing scheme and complete the Addressing Table based on the following requirements. Use the table above to help you organize your work.

a. Subnet the 192.168.1.0/24 network to provide 30 host addresses per subnet while wasting the fewest addresses.

b. Assign the fourth subnet to the IT Department LAN.

c. Assign the last network host address (the highest) in this subnet to the G0/0 interface on Town Hall.

d. Starting with the fifth subnet, subnet the network again so that the new subnets will provide 14 host addresses per subnet while wasting the fewest addresses.

e. Assign the second of these new 14-host subnets to the Administration LAN.

f. Assign the last network host address (the highest) in the Administration LAN subnet to the G0/1 interface of the Town Hall router.

g. Assign the second to the last address (the second highest) in this subnet to the VLAN 1 interface of the Administration Switch.

h. Configure addresses on the hosts using any of the remaining addresses in their respective subnets.

Step 2: Configure the Town Hall Router.

a. Configure the Town Hall router with all initial configurations that you have learned in the course so far:

· Configure the router hostname: Middle

· Protect device configurations from unauthorized access with the encrypted password.

· Secure all of the ways to access the router using methods covered in the course and labs.

· Newly-entered passwords must have a minimum length of 10 characters.

· Prevent all passwords from being viewed in clear text in device configuration files.

· Configure the router to only accept in-band management connections over the protocol that is more secure than Telnet, as was done in the labs. Use the value 1024 for encryption key strength.

· Configure user authentication for in-band management connections.

b. Configure the two Gigabit Ethernet interfaces using the IPv4 addressing values you calculated and the IPv6 values provided in the addressing table.

· Reconfigure the link local addresses as was practiced in the labs. The IPv6 link-local Interface ID should match the IPv6 unicast Interface ID as is practiced in the labs.

· Document the interfaces in the configuration file.

Step 3: Configure the Administration Switch.

Configure Administration Switch for remote management.

Step 4: Configure and Verify Host Addressing.

a. Use the IPv4 addressing from Step 1 and the IPv6 addressing values provided in the addressing table to configure all host PCs with the correct addressing.

b. Use the router interface link-local addresses as the IPv6 default gateways on the hosts.

c. All hosts should be able to ping each other over IPv4.

Step 5: Backup the Configuration of the Town Hall Router to TFTP.

a. Complete the configuration of the TFTP server using the IPv4 addressing values from Step 1 and the values in the addressing table.

b. Backup the running configuration of Town Hall to the TFTP Server. Use the default file name.

Answer

Router>
Router>enable
Router#configure terminal
Router(config)#interface g0/0
Router(config-if)#ip address 192.168.1.126 255.255.255.224
Router(config-if)#description IT Department LAN
Router(config-if)#no shutdown
Router(config-if)#exit
Router(config)#interface g0/1
Router(config-if)#ip address 192.168.1.158 255.255.255.240
Router(config-if)#description Administration LAN
Router(config-if)#no shutdown
Router(config-if)#exit
Router(config)#ipv6 unicast-routing
Router(config)#interface g0/0
Router(config-if)#ipv6 address 2001:db8:acad:A::1/64
Router(config-if)#ipv6 address FE80::1 link-local
Router(config-if)#no shutdown
Router(config-if)#exit
Router(config)#interface g0/1
Router(config-if)#ipv6 address 2001:db8:acad:B::1/64
Router(config-if)#ipv6 address FE80::1 link-local
Router(config-if)#no shutdown
Router(config-if)#exit

Router(config)#
Router(config)#hostname Middle
Middle(config)#Enable secret class12345
Middle(config)#line console 0
Middle(config-line)#password cisconet2014
Middle(config-line)#login
Middle(config-line)#exit
Middle(config)#line vty 0 15
Middle(config-line)#password cisconet2014
Middle(config-line)#login
Middle(config-line)#exit
Middle(config)#line aux 0
Middle(config-line)#password cisconet2014
Middle(config-line)#login
Middle(config-line)#exit
Middle(config)#
Middle(config)#Banner motd «Authorized Access Only»
Middle(config)#security password min-length 10
Middle(config)#service password-encryption
Middle(config)#ip domain-name ccna5.net
Middle(config)#username cisco secret cisconet2014
Middle(config)#crypto key generate rsa
The name for the keys will be: Middle.cisco.local
Choose the size of the key modulus in the range of 360 to 2048 for your
General Purpose Keys. Choosing a key modulus greater than 512 may take
a few minutes.

How many bits in the modulus [512]: 1024
% Generating 1024 bit RSA keys, keys will be non-exportable…[OK]

Middle(config)#line vty 0 15
Middle(config-line)#login local
Middle(config-line)#transport input ssh
Middle(config-line)#exit
Middle(config)#

—————————————–
Switch1 ip default gateway 192.168.1.158

—————————————–

Reception Host
default gateway FE80::1
default gateway 192.168.1.126

IP address 192.168.1.97/27
IPv6 address 2001:DB8:ACAD:A::FF/64

—————————————–

Operator Host

default gateway FE80::1
default gateway 192.168.1.126

IP address 192.168.1.98/27
IPv6 address 2001:DB8:ACAD:A::15/64

—————————————–

IT Host

default gateway FE80::1
default gateway 192.168.1.158

IP address 192.168.1.145/28
IPv6 address 2001:DB8:ACAD:B::FF/64

—————————————–

SERVER TFTP

default gateway FE80::1
default gateway 192.168.1.158

IP address 192.168.1.146/28
IPv6 address 2001:DB8:ACAD:B::15/64

—————————————–

Backup the Configuration of the Town Hall Router to TFTP.

Middle#copy running-config tftp
Address or name of remote host []? 192.168.1.146
Destination filename [Router-confg]? [Press Enter]

—————————————–

Tweet Pin It
Prev Article
Next Article

Related Articles

CCNA 1 v5 Introduction to Networks Chapter 11 Exam Answers 2014
CCNA 1 v5 Introduction to Networks Chapter 11 Exam Answers …
CCNA 1 v5.0 Routing and Switching 21 febrero, 2014 No hay comentarios

CCNA 1 v5 Introduction to Networks Chapter 11 Exam Answers 2014

CCNA 1 v5 Introduction to Networks Chapter 4 Exam Answers 2014
CCNA 1 v5 Introduction to Networks Chapter 4 Exam Answers 2014 …
CCNA 1 v5.0 Routing and Switching 10 noviembre, 2013 No hay comentarios

CCNA 1 v5 Introduction to Networks Chapter 4 Exam Answers 2014

About The Author

CisacadESP

3 Comments

  1. zeta

    You will practice and be assessed on the following skills:

    • Configuration of initial IOS device settings
    • Design and calculation of IPv4 addressing
    • Configuration of IOS device interfaces including IPv4 and IPv6 addressing when appropriate
    • Addressing of network hosts with IPv4 and IPv6 addresses
    • Enhancing device security, including configuration of the secure transport protocol for remote device configuration
    • Configuration of a switch management interface

    Requirements by device:

    • Town Hall router:
    • Configuration of initial router settings
    • Interface configuration and IPv4 and IPv6 addressing
    • Device security enhancement or “device hardening”
    • Secure transport for remote configuration connections as covered in the labs.
    • Backup of the configuration file to a TFTP server
    • Administration Switch:
    • Enabling basic remote management by Telnet
    • PC and Server hosts:
    • IPv4 full addressing
    • IPv6 addressing

    Device Interface IPv4 Address Subnet Mask IPv4 Default Gateway
    IPv6 Address IPv6 Default Gateway
    Town Hall G0/0 N/A
    2001:DB8:ACAD:A::1/64 N/A
    G0/1 N/A
    2001:DB8:ACAD:B::1/64 N/A
    Administration Switch Vlan 1
    N/A N/A
    Reception Host NIC
    2001:DB8:ACAD:A::FF
    Operator Host NIC
    2001:DB8:ACAD:A::15
    IT Host NIC
    2001:DB8:ACAD:B::FF
    TFTP Server NIC
    2001:DB8:ACAD:B::15

    Step 1: Determine the IP Addressing Scheme.
    IPv4 Subnetting Design Aid

    Design an IPv4 addressing scheme and complete the Addressing Table based on the following requirements. Use the table above to help you organize your work.
    a. Subnet the 192.168.1.0/24 network to provide 30 host addresses per subnet while wasting the fewest addresses.
    b. Assign the fourth subnet to the IT Department LAN.
    c. Assign the last network host address (the highest) in this subnet to the G0/0 interface on Town Hall.
    d. Starting with the fifth subnet, subnet the network again so that the new subnets will provide 14 host addresses per subnet while wasting the fewest addresses.
    e. Assign the second of these new 14-host subnets to the Administration LAN.
    f. Assign the last network host address (the highest) in the Administration LAN subnet to the G0/1 interface of the Town Hall router.
    g. Assign the second to the last address (the second highest) in this subnet to the VLAN 1 interface of the Administration Switch.
    h. Configure addresses on the hosts using any of the remaining addresses in their respective subnets.
    Step 2: Configure the Town Hall Router.
    a. Configure the Town Hall router with all initial configurations that you have learned in the course so far:
    • Configure the router hostname: Middle
    • Protect device configurations from unauthorized access with the encrypted password.
    • Secure all of the ways to access the router using methods covered in the course and labs.
    • Newly-entered passwords must have a minimum length of 10 characters.
    • Prevent all passwords from being viewed in clear text in device configuration files.
    • Configure the router to only accept in-band management connections over the protocol that is more secure than Telnet, as was done in the labs. Use the value 1024 for encryption key strength.
    • Configure user authentication for in-band management connections.
    b. Configure the two Gigabit Ethernet interfaces using the IPv4 addressing values you calculated and the IPv6 values provided in the addressing table.
    • Reconfigure the link local addresses as was practiced in the labs. The IPv6 link-local Interface ID should match the IPv6 unicast Interface ID as is practiced in the labs.
    • Document the interfaces in the configuration file.
    Step 3: Configure the Administration Switch.
    Configure Administration Switch for remote management.
    Step 4: Configure and Verify Host Addressing.
    a. Use the IPv4 addressing from Step 1 and the IPv6 addressing values provided in the addressing table to configure all host PCs with the correct addressing.
    b. Use the router interface link-local addresses as the IPv6 default gateways on the hosts.
    c. All hosts should be able to ping each other over IPv4.
    Step 5: Backup the Configuration of the Town Hall Router to TFTP.
    a. Complete the configuration of the TFTP server using the IPv4 addressing values from Step 1 and the values in the addressing table.
    b. Backup the running configuration of Town Hall to the TFTP Server. Use the default file name.

    29 enero, 2014
    • Marlon

      I just now wanted to thank you yet again for that amanzig web site you have created here. It is full of useful tips for those who are seriously interested in this subject

      21 febrero, 2016
  2. telefoojay

    Hi
    I’ve a different skills assessment has anyone else
    It’s
    Part one develop the ipv4 address scheme(2subnets)
    Part two-initialize and reload devices
    Part 3-configure device ipv4 and security settings
    Part 4-test and verify ipv4 end to end connectivity
    Part 5-configure ipv6 addressing on r1
    Part 6-test and verify ipv6 end to end connectivity
    Part 7-use the iOS cli to gather device info
    Part 8-save the r1 config to a tftp server

    Anyone help me out?
    Please

    28 enero, 2014

Leave a Reply Cancel Reply

Este sitio usa Akismet para reducir el spam. Aprende cómo se procesan los datos de tus comentarios.

CCNA v7.0 en Español Preguntas y Respuestas

  • CCNA 1
  • CCNA 2
  • CCNA 3
  • Módulos 1 - 3: Examen de conectividad de red básica y comunicaciones
  • Módulos 4 - 7: Examen de conceptos Ethernet
  • Módulos 8 - 10: Examen de comunicación entre redes
  • Módulos 11 - 13: Examen de direccionamiento IP
  • Módulos 14 - 15: Examen de comunicaciones de aplicaciones de red
  • Módulos 16 - 17: Examen de crear y asegurar una red pequeña
  • Evaluación de habilidades prácticas de PT (PTSA)
  • CCNA 1 v7 Examen Final de Práctica Respuestas
  • CCNA 1 v7 Examen Final de habilidades ITN (PTSA) Respuestas
  • CCNA 1 Examen Final Preguntas y Respuestas
  • Módulos 1 - 4: Examen de conceptos de Switching, VLANs y enrutamiento entre redes VLAN
  • Módulos 5 - 6: Examen de Redes Redundantes
  • Módulos 7 - 9: Examen de redes Disponibles y Confiables
  • Módulos 10 - 13: Examen de seguridad L2 y WLAN
  • Módulos 14 - 16: Examen de conceptos de enrutamiento y configuración
  • Evaluación de habilidades prácticas de PT (PTSA) SRWE - Parte 1
  • Evaluación de habilidades prácticas de PT (PTSA) SRWE - Parte 2
  • CCNA 2 Examen Practico Final - SRWE Preguntas y Respuestas
  • Examen Final de Habilidades SRWE (PTSA) Respuestas
  • CCNA 2 Examen Final de SRWE Preguntas y Respuestas
  • Módulos 1 - 2: Examen de conceptos OSPF y configuración
  • Módulos 3 - 5: Examen de seguridad de la red
  • Módulos 6 - 8: Examen de conceptos de WAN
  • Módulos 9 - 12: Examen de optimización, supervisión y solución de problemas de redes
  • Módulos 13 - 14: Examen de Tecnologías de Redes Emergentes
  • Evaluación de habilidades prácticas de PT (PTSA) ENSA Respuestas
  • CCNA 3 Examen Practico Final - ENSA Preguntas y Respuestas
  • Examen Final de Habilidades ENSA (PTSA) Respuestas
  • CCNA 3 Examen Final de ENSA Preguntas y Respuestas Opcion A
  • CCNA 3 Examen Final de ENSA Preguntas y Respuestas Opcion B
  • Examen de práctica de certificación CCNA (200-301) Respuestas

CCNA v7.0 in English

  • CCNA 1 v7.0
  • CCNA 2 v7.0
  • CCNA 3 v7.0
Examen Modulos 1 – 3 Respuestas Examen Modulos 4 – 7 Respuestas Examen Modulos 8 – 10 Respuestas Examen Modulos 11 – 13 Respuestas Examen Modulos 14 – 15 Respuestas Examen Modulos 16 – 17 Respuestas CCNA 1 v7 Practice Skill Assessment CCNA 1 v7 Practice Final Exam CCNA 1 v7 Practice Final Exam
Examen Modulos 1 – 4 Respuestas Examen Modulos 5 – 6 Respuestas Examen Modulos 7 – 9 Respuestas Examen Modulos 10 – 13 Respuestas Examen Modulos 14 – 16 Respuestas CCNA 2 v7 Practice Skill Assessment
Examen Modulos 1 – 2 Respuestas Examen Modulos 3 – 5 Respuestas Examen Modulos 6 – 8 Respuestas Examen Modulos 9 – 12 Respuestas Examen Modulos 13 – 14 Respuestas CCNA 3 v7 Practice Skill Assessment

Cisacad.net

Examenes Cisco CCNA v7.0 y IT Essentials v8 en Español
Copyright © 2023 Cisacad.net
Política de Privacidad CCNA v7.0 y v6.0 Examenes Cisco 2021 - Cisacad.net
Utilizamos cookies en nuestro sitio web para ofrecerle la experiencia más relevante al recordar sus preferencias y visitas repetidas. Al hacer clic en "Aceptar", usted consiente el uso de TODAS las cookies.
No vender mi información personal..
Cookies configuraciónACEPTO
Manage consent

Resumen de la privacidad

Este sitio web utiliza cookies para mejorar su experiencia mientras navega por el sitio web. De ellas, las cookies clasificadas como necesarias se almacenan en su navegador, ya que son esenciales para el funcionamiento de las funciones básicas del sitio web. También utilizamos cookies de terceros que nos ayudan a analizar y comprender cómo utiliza usted este sitio web. Estas cookies se almacenan en su navegador sólo con su consentimiento. También tiene la opción de excluirse de estas cookies. Pero la exclusión de algunas de estas cookies puede afectar a su experiencia de navegación.
Necesarias
Siempre activado
Las cookies necesarias son absolutamente imprescindibles para que el sitio web funcione correctamente. Estas cookies garantizan las funcionalidades básicas y las características de seguridad del sitio web, de forma anónima.
CookieDuraciónDescripción
cookielawinfo-checbox-analytics11 monthsEsta cookie es establecida por el plugin GDPR Cookie Consent. La cookie se utiliza para almacenar el consentimiento del usuario para las cookies de la categoría "Analytics".
cookielawinfo-checbox-functional11 monthsLa cookie se establece por el consentimiento de cookies GDPR para registrar el consentimiento del usuario para las cookies en la categoría "Funcional".
cookielawinfo-checbox-others11 monthsEsta cookie es establecida por el plugin GDPR Cookie Consent. La cookie se utiliza para almacenar el consentimiento del usuario para las cookies de la categoría "Otros".
cookielawinfo-checkbox-necessary11 monthsEsta cookie es establecida por el plugin GDPR Cookie Consent. Las cookies se utilizan para almacenar el consentimiento del usuario para las cookies en la categoría "Necesario".
cookielawinfo-checkbox-performance11 monthsEsta cookie es establecida por el plugin GDPR Cookie Consent. La cookie se utiliza para almacenar el consentimiento del usuario para las cookies de la categoría "Rendimiento".
viewed_cookie_policy11 monthsLa cookie es establecida por el plugin GDPR Cookie Consent y se utiliza para almacenar si el usuario ha consentido o no el uso de cookies. No almacena ningún dato personal.
Funcional
Las cookies funcionales ayudan a realizar ciertas funcionalidades como compartir el contenido del sitio web en las plataformas de las redes sociales, recoger opiniones y otras características de terceros.
Rendimiento
Las cookies de rendimiento se utilizan para entender y analizar los índices de rendimiento clave del sitio web, lo que ayuda a ofrecer una mejor experiencia de usuario a los visitantes.
Analytics
Las cookies analíticas se utilizan para entender cómo interactúan los visitantes con el sitio web. Estas cookies ayudan a proporcionar información sobre las métricas del número de visitantes, la tasa de rebote, la fuente de tráfico, etc.
Publicidad
Las cookies de publicidad se utilizan para ofrecer a los visitantes anuncios y campañas de marketing relevantes. Estas cookies rastrean a los visitantes en todos los sitios web y recopilan información para ofrecer anuncios personalizados.
Otras
Otras cookies no categorizadas son aquellas que están siendo analizadas y que aún no han sido clasificadas en una categoría.
GUARDAR Y ACEPTAR