CCNA 2 Chapter 7 v5.0 Exam Answers 2014

By | 20 noviembre, 2013

CCNA 2 Chapter 7 v5.0 Exam Answers 2014 1 What is the purpose of the passive-interface command? allows interfaces to share IP addresses allows an interface to remain up without receiving keepalives allows a router to send routing updates on an interface but not receive updates via that innterface allows a routing protocol to forward updates out an… Read More »

CCNA 2 Chapter 6 v5.0 Exam Answers 2014

By | 20 noviembre, 2013

CCNA 2 Chapter 6 v5.0 Exam Answers 2014 1 What are two advantages of static routing over dynamic routing? (Choose two.) Static routing is more secure because it does not advertise over the network.* Static routing is relatively easy to configure for large networks. Static routing requires very little knowledge of the network for correct implementation. Static routing… Read More »

CCNA 2 Chapter 5 v5.0 Exam Answers 2014

By | 19 noviembre, 2013

CCNA 2 Chapter 5 v5.0 Exam Answers 2014 1 Fill in the blank. Do not use abbreviations. A network engineer is troubleshooting the configuration of new VLANs on a network. ​Which command is used to display the list of VLANs that exists on the switch? ” show vlan ” 2 What is a disadvantage of using multilayer switches… Read More »

CCNA 2 Chapter 4 v5.0 Exam Answers 2014

By | 19 noviembre, 2013

CCNA 2 Chapter 4 v5.0 Exam Answers 2014 1 What type of IPv6 address is required as a minimum on IPv6 enabled interfaces? static global unicast link-local* loopback unique local 2 In order for packets to be sent to a remote destination, what three pieces of information must be configured on a host? (Choose three.) default gateway* hostname… Read More »

CCNA 2 Chapter 3 v5.0 Exam Answers 2014

By | 19 noviembre, 2013

CCNA 2 Chapter 3 v5.0 Exam Answers 2014 1 A network administrator is determining the best placement of VLAN trunk links. Which two types of point-to-point connections utilize VLAN trunking?​ (Choose two.) between two switches that share a common VLAN between a switch and a server that has an 802.1Q NIC* between a switch and a client PC… Read More »

CCNA 2 Chapter 2 v5.0 Exam Answers 2014

By | 17 noviembre, 2013

CCNA 2 Chapter 2 v5.0 Exam Answers 2014 1 Which type of cable does a network administrator need to connect a PC to a switch to recover it after the Cisco IOS software fails to load? a coaxial cable a crossover cable a straight-through cable a console cable* 2 Which two basic functions are performed by network security… Read More »

CCNA 2 Chapter 1 v5.0 Exam Answers 2014

By | 13 noviembre, 2013

CCNA 2 Chapter 1 v5.0 Exam Answers 2014 1 What is one advantage of using the cut-through switching method instead of the store-and-forward switching method? has a positive impact on bandwidth by dropping most of the invalid frames makes a fast forwarding decision based on the source MAC address of the frame has a lower latency appropriate for… Read More »

CCNA 1 Routing and Switching: Introduction to Networks Final Exam

By | 13 noviembre, 2013

CCNA 1 v5.0 R&S ITN Final Exam 2014 1 Refer to the exhibit. The network administrator enters these commands into the R1 router: R1# copy running-config tftp Address or name of remote host [ ]? When the router prompts for an address or remote host name, what IP address should the administrator enter at the prompt? 192.168.9.254 192.168.10.1 192.168.10.2… Read More »

CCNA 1 v5 Introduction to Networks Pretest Exam Answers 2014

By | 12 noviembre, 2013

CCNA 1 v5 Introduction to Networks Pretest Exam Answers 2014 1 2 The failure rate in a certain brand of network interface card has been determined to be 15%. How many cards could be expected to fail in a company that has 80 of the cards installed? 10 12* 15 8 3 If a technician uses an average… Read More »

CCNA 1 v5 Introduction to Networks Chapter 10 Exam Answers 2014

By | 11 noviembre, 2013

CCNA 1 v5 Introduction to Networks Chapter 10 Exam Answers 2014 1 Which three layers of the OSI model provide similar network services to those provided by the application layer of the TCP/IP model? (Choose three.) physical layer session layer* transport layer application layer* presentation layer* data link layer 2 Which two tasks are functions of the presentation layer?… Read More »