Cisacad.net

Examenes Cisco CCNA v7.0 y IT Essentials v8 en Español
Menu
  • Inicio
  • CCNA v7.02
    • CCNA 1 v7.02
    • CCNA 2 v7.02
    • CCNA 3 v7.02
  • CCNA v6.0
    • CCNA 1 v6.0
    • CCNA 2 v6.0
    • CCNA 3 v6.0
    • CCNA 4 v6.0
  • CCNA v5.0
    • Exámenes Cisco CCNA 1 v.5.0
    • Exámenes Cisco CCNA 2 v.5.0
    • Exámenes Cisco CCNA 3 v.5.0
    • Exámenes Cisco CCNA 4 v.5.0
  • Security
    • Network Security v1.0
    • CCNA Security 2.0
  • It-essentials v7.01
  • Ciberseguridad
    • Introducción a la Ciberseguridad v2.1
    • Cybersecurity Essentials v1.1
  • Mas Cursos
    • Introduccion a IoT v2.0
    • GetConnected
    • Networking Essentials v2
    • Entrepreneurship

CCNA 1 v5 Introduction to Networks Chapter 5 Exam Answers 2014

CCNA 1 v5 Introduction to Networks Chapter 5 Exam Answers 2014

1

2
A host is trying to send a packet to a device on a remote LAN segment, but there are currently no mappings in its ARP cache. How will the device obtain a destination MAC address?

It will send a request to the DNS server for the destination MAC address.

It will send an ARP request for the MAC address of the destination device.

It will send the frame and use its own MAC address as the destination.

It will send the frame with a broadcast MAC address.

It will send an ARP request for the MAC address of the default gateway.*

3
Which address or combination of addresses does a Layer 3 switch use to make forwarding decisions?

MAC and IP addresses*

MAC address only

MAC and port addresses

port address only

IP address only

4
What are two potential network problems that can result from ARP operation? (Choose two.)

Multiple ARP replies result in the switch MAC address table containing entries that match the MAC addresses of hosts that are connected to the relevant switch port.

On large networks with low bandwidth, multiple ARP broadcasts could cause data communication delays.*

Network attackers could manipulate MAC address and IP address mappings in ARP messages with the intent of intercepting network traffic.*

Manually configuring static ARP associations could facilitate ARP poisoning or MAC address spoofing.

Large numbers of ARP request broadcasts could cause the host MAC address table to overflow and prevent the host from communicating on the network.

5

Launch PT Hide and Save PT
Open the PT Activity. Perform the tasks in the activity instruction and then answer the question.

What destination address will PC1 include in the destination address field of the Ethernet frame that it sends to PC2?
00e0.b0be.8014

0030.a3e5.0401*

192.168.0.34

192.168.0.17

0007.ec35.a5c6

6
How does adding an Ethernet line card affect the form factor of a switch?

by increasing the back plane switching speed

by expanding the port density*

by expanding the NVRAM capacity

by making the switch stackable

7
Which two statements are correct about MAC and IP addresses during data transmission if NAT is not involved? (Choose two.)

Destination MAC addresses will never change in a frame that goes across seven routers.

A packet that has crossed four routers has changed the destination IP address four times.

Destination and source MAC addresses have local significance and change every time a frame goes from one LAN to another.*

Destination IP addresses in a packet header remain constant along the entire path to a target host.*

Every time a frame is encapsulated with a new destination MAC address, a new destination IP address is needed.

8
What is the Layer 2 multicast MAC address that corresponds to the Layer 3 IPv4 multicast address 224.139.34.56?

FE-80-00-0B-22-38

01-00-5E-0B-22-38*

FF-FF-FF-0B-22-38

00-00-00-0B-22-38

01-5E-00-0B-22-38

9
What is the purpose of the preamble in an Ethernet frame?

is used to identify the destination address

is used to identify the source address

is used as a padding for data

is used for timing synchronization*

10
A Layer 2 switch is used to switch incoming frames from a 1000BASE-T port to a port connected to a 100Base-T network. Which method of memory buffering would work best for this task?

level 1 cache buffering

shared memory buffering*

fixed configuration buffering

port-based buffering

11
A network administrator is connecting two modern switches using a straight-through cable. The switches are new and have never been configured. Which three statements are correct about the final result of the connection? (Choose three.)

The auto-MDIX feature will configure the interfaces eliminating the need for a crossover cable.*

The connection will not be possible unless the administrator changes the cable to a crossover cable.

The duplex capability has to be manually configured because it cannot be negotiated.

If both switches support different speeds, they will each work at their own fastest speed.

The link between switches will work as full-duplex.*

The link between the switches will work at the fastest speed that is supported by both switches.*

12


Refer to the exhibit. PC1 issues an ARP request because it needs to send a packet to PC2. In this scenario, what will happen next?​

RT1 will send an ARP reply with its Fa0/0 MAC address.​

PC2 will send an ARP reply with its MAC address.*

RT1 will send an ARP reply with the PC2 MAC address.​

SW1 will send an ARP reply with its Fa0/1 MAC address.​

SW1 will send an ARP reply with the PC2 MAC address.​

13
What is a characteristic of a contention-based access method?

It processes more overhead than the controlled access methods do.

It scales very well under heavy media use.

It is a nondeterministic method.*

It has mechanisms to track the turns to access the media.

14
What statement illustrates a drawback of the CSMA/CD access method?

Collisions can decrease network performance.*

Deterministic media access protocols slow network performance.

CSMA/CD LAN technologies are only available at slower speeds than other LAN technologies.

It is more complex than non-deterministic protocols.
15
When would a switch record multiple entries for a single switch port in its MAC address table?

when the switch is configured for Layer 3 switching

when another switch is connected to the switch port*

when a router is connected to the switch port

when multiple ARP broadcasts have been forwarded
16
Which two statements describe a fixed configuration Ethernet switch? (Choose two.)

An SVI cannot be configured on the switch.

A fixed configuration switch may be stackable.*

The number of ports on the switch cannot be increased.*

The port density of the switch is determined by the Cisco IOS.

The switch cannot be configured with multiple VLANs.

17
Which two statements describe features or functions of the logical link control sublayer in Ethernet standards? (Choose two.)

Logical link control is implemented in software.*

The LLC sublayer interacts directly with the NIC driver software.

The data link layer uses LLC to communicate with the upper layers of the protocol suite.*

The LLC sublayer is responsible for the placement and retrieval of frames on and off the media.

Logical link control is specified in the IEEE 802.3 standard.
18
A network administrator issues the following commands on a Layer 3 switch:

DLS1(config)# interface f0/3
DLS1(config-if)# no switchport
DLS1(config-if)# ip address 172.16.0.1 255.255.255.0
DLS1(config-if)# no shutdown
DLS1(config-if)# end

What is the administrator configuring?

a Cisco Express Forwarding instance

a routed port*

a trunk interface

a switched virtual interface

19
Which statement is true about MAC addresses?

The first three bytes are used by the vendor assigned OUI.*

MAC addresses are implemented by software.

The ISO is responsible for MAC addresses regulations.

A NIC only needs a MAC address if connected to a WAN.

20

Refer to the exhibit. The exhibit shows a small switched network and the contents of the MAC address table of the switch. PC1 has sent a frame addressed to PC3. What will the switch do with the frame?

The switch will forward the frame to all ports.

The switch will forward the frame to all ports except port 4.*

The switch will forward the frame only to port 2.

The switch will discard the frame.

The switch will forward the frame only to ports 1 and 3.
21
Fill in the blank.
The binary number 0000 1010 can be expressed as «A» in hexadecimal.
22
What are two features of ARP? (Choose two.)

If a host is ready to send a packet to a local destination device and it has the IP address but not the MAC address of the destination, it generates an ARP broadcast.*

An ARP request is sent to all devices on the Ethernet LAN and contains the IP address of the destination host and its multicast MAC address.

When a host is encapsulating a packet into a frame, it refers to the MAC address table to determine the mapping of IP addresses to MAC addresses.

If a device receiving an ARP request has the destination IPv4 address, it responds with an ARP reply.*

If no device responds to the ARP request, then the originating node will broadcast the data packet to all devices on the network segment.

23

 

 

Tweet Pin It
Prev Article
Next Article

Related Articles

CCNA 1 v5 Introduction to Networks Chapter 9 Exam Answers 2014
CCNA 1 v5 Introduction to Networks Chapter 9 Exam Answers 2014 …
CCNA 1 v5.0 Routing and Switching 11 noviembre, 2013 No hay comentarios

CCNA 1 v5 Introduction to Networks Chapter 9 Exam Answers 2014

CCNA 1 v5 Introduction to Networks Chapter 10 Exam Answers 2014
CCNA 1 v5 Introduction to Networks Chapter 10 Exam Answers 2014 …
CCNA 1 v5.0 Routing and Switching 11 noviembre, 2013 2 comentarios

CCNA 1 v5 Introduction to Networks Chapter 10 Exam Answers 2014

About The Author

CisacadESP

One Response

  1. john

    Can you please add a PDF answer file

    18 noviembre, 2013

Leave a Reply Cancel Reply

Este sitio usa Akismet para reducir el spam. Aprende cómo se procesan los datos de tus comentarios.

CCNA v7.0 en Español Preguntas y Respuestas

  • CCNA 1
  • CCNA 2
  • CCNA 3
  • Módulos 1 - 3: Examen de conectividad de red básica y comunicaciones
  • Módulos 4 - 7: Examen de conceptos Ethernet
  • Módulos 8 - 10: Examen de comunicación entre redes
  • Módulos 11 - 13: Examen de direccionamiento IP
  • Módulos 14 - 15: Examen de comunicaciones de aplicaciones de red
  • Módulos 16 - 17: Examen de crear y asegurar una red pequeña
  • Evaluación de habilidades prácticas de PT (PTSA)
  • CCNA 1 v7 Examen Final de Práctica Respuestas
  • CCNA 1 v7 Examen Final de habilidades ITN (PTSA) Respuestas
  • CCNA 1 Examen Final Preguntas y Respuestas
  • Módulos 1 - 4: Examen de conceptos de Switching, VLANs y enrutamiento entre redes VLAN
  • Módulos 5 - 6: Examen de Redes Redundantes
  • Módulos 7 - 9: Examen de redes Disponibles y Confiables
  • Módulos 10 - 13: Examen de seguridad L2 y WLAN
  • Módulos 14 - 16: Examen de conceptos de enrutamiento y configuración
  • Evaluación de habilidades prácticas de PT (PTSA) SRWE - Parte 1
  • Evaluación de habilidades prácticas de PT (PTSA) SRWE - Parte 2
  • CCNA 2 Examen Practico Final - SRWE Preguntas y Respuestas
  • Examen Final de Habilidades SRWE (PTSA) Respuestas
  • CCNA 2 Examen Final de SRWE Preguntas y Respuestas
  • Módulos 1 - 2: Examen de conceptos OSPF y configuración
  • Módulos 3 - 5: Examen de seguridad de la red
  • Módulos 6 - 8: Examen de conceptos de WAN
  • Módulos 9 - 12: Examen de optimización, supervisión y solución de problemas de redes
  • Módulos 13 - 14: Examen de Tecnologías de Redes Emergentes
  • Evaluación de habilidades prácticas de PT (PTSA) ENSA Respuestas
  • CCNA 3 Examen Practico Final - ENSA Preguntas y Respuestas
  • Examen Final de Habilidades ENSA (PTSA) Respuestas
  • CCNA 3 Examen Final de ENSA Preguntas y Respuestas Opcion A
  • CCNA 3 Examen Final de ENSA Preguntas y Respuestas Opcion B
  • Examen de práctica de certificación CCNA (200-301) Respuestas

CCNA v7.0 in English

  • CCNA 1 v7.0
  • CCNA 2 v7.0
  • CCNA 3 v7.0
Examen Modulos 1 – 3 Respuestas Examen Modulos 4 – 7 Respuestas Examen Modulos 8 – 10 Respuestas Examen Modulos 11 – 13 Respuestas Examen Modulos 14 – 15 Respuestas Examen Modulos 16 – 17 Respuestas CCNA 1 v7 Practice Skill Assessment CCNA 1 v7 Practice Final Exam CCNA 1 v7 Practice Final Exam
Examen Modulos 1 – 4 Respuestas Examen Modulos 5 – 6 Respuestas Examen Modulos 7 – 9 Respuestas Examen Modulos 10 – 13 Respuestas Examen Modulos 14 – 16 Respuestas CCNA 2 v7 Practice Skill Assessment
Examen Modulos 1 – 2 Respuestas Examen Modulos 3 – 5 Respuestas Examen Modulos 6 – 8 Respuestas Examen Modulos 9 – 12 Respuestas Examen Modulos 13 – 14 Respuestas CCNA 3 v7 Practice Skill Assessment

Cisacad.net

Examenes Cisco CCNA v7.0 y IT Essentials v8 en Español
Copyright © 2023 Cisacad.net
Política de Privacidad CCNA v7.0 y v6.0 Examenes Cisco 2021 - Cisacad.net
Utilizamos cookies en nuestro sitio web para ofrecerle la experiencia más relevante al recordar sus preferencias y visitas repetidas. Al hacer clic en "Aceptar", usted consiente el uso de TODAS las cookies.
No vender mi información personal..
Cookies configuraciónACEPTO
Manage consent

Resumen de la privacidad

Este sitio web utiliza cookies para mejorar su experiencia mientras navega por el sitio web. De ellas, las cookies clasificadas como necesarias se almacenan en su navegador, ya que son esenciales para el funcionamiento de las funciones básicas del sitio web. También utilizamos cookies de terceros que nos ayudan a analizar y comprender cómo utiliza usted este sitio web. Estas cookies se almacenan en su navegador sólo con su consentimiento. También tiene la opción de excluirse de estas cookies. Pero la exclusión de algunas de estas cookies puede afectar a su experiencia de navegación.
Necesarias
Siempre activado
Las cookies necesarias son absolutamente imprescindibles para que el sitio web funcione correctamente. Estas cookies garantizan las funcionalidades básicas y las características de seguridad del sitio web, de forma anónima.
CookieDuraciónDescripción
cookielawinfo-checbox-analytics11 monthsEsta cookie es establecida por el plugin GDPR Cookie Consent. La cookie se utiliza para almacenar el consentimiento del usuario para las cookies de la categoría "Analytics".
cookielawinfo-checbox-functional11 monthsLa cookie se establece por el consentimiento de cookies GDPR para registrar el consentimiento del usuario para las cookies en la categoría "Funcional".
cookielawinfo-checbox-others11 monthsEsta cookie es establecida por el plugin GDPR Cookie Consent. La cookie se utiliza para almacenar el consentimiento del usuario para las cookies de la categoría "Otros".
cookielawinfo-checkbox-necessary11 monthsEsta cookie es establecida por el plugin GDPR Cookie Consent. Las cookies se utilizan para almacenar el consentimiento del usuario para las cookies en la categoría "Necesario".
cookielawinfo-checkbox-performance11 monthsEsta cookie es establecida por el plugin GDPR Cookie Consent. La cookie se utiliza para almacenar el consentimiento del usuario para las cookies de la categoría "Rendimiento".
viewed_cookie_policy11 monthsLa cookie es establecida por el plugin GDPR Cookie Consent y se utiliza para almacenar si el usuario ha consentido o no el uso de cookies. No almacena ningún dato personal.
Funcional
Las cookies funcionales ayudan a realizar ciertas funcionalidades como compartir el contenido del sitio web en las plataformas de las redes sociales, recoger opiniones y otras características de terceros.
Rendimiento
Las cookies de rendimiento se utilizan para entender y analizar los índices de rendimiento clave del sitio web, lo que ayuda a ofrecer una mejor experiencia de usuario a los visitantes.
Analytics
Las cookies analíticas se utilizan para entender cómo interactúan los visitantes con el sitio web. Estas cookies ayudan a proporcionar información sobre las métricas del número de visitantes, la tasa de rebote, la fuente de tráfico, etc.
Publicidad
Las cookies de publicidad se utilizan para ofrecer a los visitantes anuncios y campañas de marketing relevantes. Estas cookies rastrean a los visitantes en todos los sitios web y recopilan información para ofrecer anuncios personalizados.
Otras
Otras cookies no categorizadas son aquellas que están siendo analizadas y que aún no han sido clasificadas en una categoría.
GUARDAR Y ACEPTAR