CCNA 4 R&S Connecting Networks v5.0 Practice Skills Assessment – Packet Tracer

CCNA Routing and Switching
Connecting Networks

Practice Skills Assessment – Packet Tracer

A few things to keep in mind while completing this activity:

Do not use the browser Back button or close or reload any exam windows during the exam.
Do not close Packet Tracer when you are done. It will close automatically.
Click the Submit Assessment button in the browser window to submit your work.

Introduction

In this practice skills assessment, you will configure the Small Business network with NTP, SNMP, EIGRP, PPP CHAP, Frame Relay, dynamic NAT, static NAT, PAT and a GRE tunnel.

Some values that are required to complete the configurations may not have been given to you. In that case, create the values that you need to complete the requirements.

For the sake of time, many repetitive, but important, configuration tasks have been omitted from this assessment. Many of these tasks, especially those related to security, are essential elements of a network configuration. The intent of this activity is not to diminish the importance of full device configurations.

You will practice and be assessed on the following skills:

Configuration of NTP
Configuration of SNMP and Syslog
Configuration of interface addressing and basic settings
Configuration of HDLC
Configuration of Frame Relay
Configuration of PPP
Configuration of CHAP
Configuration of a GRE tunnel
Configuration of static and dynamic routing
Configuration of dynamic NAT
Configuration of static NAT
Configuration of PAT

You are required to configure the devices as follows:

Office-1:

Configure HDLC.
Configure EIGRP.
Configure passive interfaces.

R2:

Configure PPP and CHAP authentication on the appropriate interface.
Configure EIGRP.
Configure static NAT for outside access to an internal server.
Configure dynamic NAT.
Configure PAT.

R3:

Enable time stamps for use with NTP and SNMP logging.
Configure the router to use NTP services.
Configure logging to the IT Monitor Server.
Configure PPP and CHAP authentication on the appropriate interface.
Configure Frame Relay.
Configure a GRE tunnel.
Configure EIGRP.
Configure passive interfaces.

Office-2-Branch:

Configure Frame Relay.
Configure a GRE tunnel.
Configure EIGRP.
Configure passive Interfaces.

Tables

In some cases, specific interface addresses have been provided to you. You must use them in your configurations. In other cases, when a network is specified instead of a specific address, you can use any address in the network.

You do not configure LAN addresses in this activity. The addresses of the LAN interfaces are provided in this table for reference purposes only.

Device	Interface	IP Address or Network	Default Gateway
Office-1	G0/1	192.168.1.1/24	N/A
Office-1	S0/0/0	192.168.0.0/30	N/A
R2	G0/0	172.16.0.1/30	N/A
	S0/0/0	192.168.0.0/30	N/A
	S0/0/1	10.10.0.0/30	N/A
	S0/1/0	203.0.113.1/28	N/A
R3	G0/1	10.10.1.1/24	N/A
	S0/0/0	10.10.2.1/30	N/A
	S0/0/1	10.10.0.0/30	N/A
	T0	10.10.10.1/30	N/A
Office-2-Branch	G0/0	10.10.3.1/24	N/A
	S0/0/0	10.10.2.2/30	N/A
	T0	10.10.10.2/30	N/A
Partner Server	NIC	172.16.0.2/30	172.16.0.1
IT Monitor Server	NIC	10.10.1.2/24	10.10.1.1
Office-1 PC	NIC	192.168.1.5/24	192.168.1.1
R3 Host	NIC	10.10.1.5/24	10.10.1.1
Office-2 Branch PC	NIC	10.10.3.5/24	10.10.3.1

Instructions

All configurations must be performed through a direct terminal connection to the device console from an available host.

Step 1: Configure NTP, SNMP, and Syslog settings on R3.

a. Configure NTP.

Configure R3 to use IT Monitor Server as its NTP server.
Use a key value of 15.

b. Configure SNMP.

Use an SNMP community string of CiscoPTSA.
Allow the SNMP management station only read only rights.

c. Configure Syslog.

Configure R3 to use time stamps when logging. The timestamps should include milliseconds.
Configure Syslog to send log entries to the IT Monitor Server.
Set the message trapping for Syslog to the debugging level.

Step 2: Configure Frame Relay between R3 and Office-2-Branch.

Configure Frame Relay on the interfaces connecting R3 and Office-2-Branchusing the information from the Addressing Table. You must use the exact addresses specified in the addressing table for the configuration.

Step 3: Configure a GRE Tunnel between R3 and Office-2-Branch.

Configure a GRE tunnel using Tunnel interface 0 on R3 to Office-2-Branch using information from the addressing table.
Configure a GRE tunnel using Tunnel interface 0 on Office-2-Branchto R3 using information from the addressing table.
You must use the exact addresses specified in the addressing table for this configuration.

Step 4: Configure DCE interfaces.

Configure the DCE interfaces of R2 with a clock rate of 128000.

Step 5: Configure PPP and CHAP between R2 and R3.

Configure interface addressing according to information provided in the Addressing Table. You can use any address in the network specified in the Addressing Table for this configuration.
Authenticate the PPP connection with CHAP on both ends of the link.
Use the password of PTSAchap.

Step 6: Configure HDLC on Office-1 and R2.

It has been decided to remove an earlier PPP configuration from the link between Office-1 and R2.

Configure this link with HDLC.
Configure interface addressing according to information provided in the Addressing Table. You can use any address in the network specified in the Addressing Table.

Step 7: Configure NAT on R2.

All hosts should use translated addresses to access destinations outside of the Small Business network.

a. Configure static NAT.

Configure static NAT for the IP address of the Partner Server.
Use the last host address in the interface S0/1/0 subnet.

b. Configure dynamic NAT.

Configure dynamic NAT for all host IP addresses on the LAN network connected to Office-1.
Use DYNAMIC as the name for the pool.
Use the third through tenth IP addresses that are available on the R2 S0/1/0 subnet.
Configure ACL 1 to allow all host IP addresses in Office-1 LAN network to use this group of addresses.
Your ACL should have one statement.

c. Configure PAT.

Configure PAT to enable the hosts attached to the R3 and Office-2-Branch LANs to access the Internet.
Use the interface keyword in the NAT statement.
Use ACL 2 to allow all host addresses on both LAN networks to use the overload address.
Your ACL should have two statements.
Configure all interfaces on R2 as appropriate.

Step 8: Configure static and dynamic routing.

a. Configure dynamic routing.

Configure EIGRP for all networks connected to Office-1, R2,R3, and Office-2-Branch.
Use ASN 1.
Use the precise inverse masks for all networks.
Disable automatic summarization on all routers.
Disable EIGRP updates from being sent on the appropriate interfaces. You must do this for each individual interface. Donot use the default keyword with the command.

b. Configure a redistribute a default route.

Create a directly attached default route to the Internet on R2.
Configure EIGRP to redistribute the default route to the other routers.

CisacadESP

2 Comments

Edinson Acevedo

HQ#sh run
Building configuration…

Current configuration : 1637 bytes
!
version 15.1
no service timestamps log datetime msec
no service timestamps debug datetime msec
no service password-encryption
!
hostname HQ
!
ip cef
no ipv6 cef

!
username Office-2 password 0 PTSAchap
!
license udi pid CISCO1941/K9 sn FTX1524GSCZ
!
spanning-tree mode pvst
!
interface GigabitEthernet0/0
ip address 172.16.0.1 255.255.255.252
ip nat inside
duplex auto
speed auto
!
interface GigabitEthernet0/1
no ip address
duplex auto
speed auto
shutdown
!
interface Serial0/0/0
ip address 192.168.0.1 255.255.255.252
ip nat inside
clock rate 128000
!
interface Serial0/0/1
ip address 10.10.0.1 255.255.255.252
encapsulation ppp
ppp authentication chap
ip nat inside
clock rate 128000
!
interface Serial0/1/0
ip address 203.0.113.1 255.255.255.240
ip nat outside
!
interface Serial0/1/1
no ip address
clock rate 2000000
shutdown
!
interface Vlan1
no ip address
shutdown
!
router eigrp 1
redistribute static
passive-interface GigabitEthernet0/0
network 172.16.0.0 0.0.0.3
network 192.168.0.0 0.0.0.3
network 10.10.0.0 0.0.0.3
network 203.0.113.0 0.0.0.15
!
ip nat pool DYNAMIC 203.0.113.3 203.0.113.10 netmask 255.255.255.240
ip nat inside source list 1 pool DYNAMIC
ip nat inside source list 2 interface Serial0/1/0 overload
ip nat inside source static 172.16.0.2 203.0.113.14
ip classless
ip route 0.0.0.0 0.0.0.0 Serial0/1/0
!
ip flow-export version 9
!
!
access-list 1 permit 192.168.1.0 0.0.0.255
access-list 2 permit 10.10.1.0 0.0.0.255
access-list 2 permit 10.10.3.0 0.0.0.255
!
line con 0
!
line aux 0
!
line vty 0 4
login
!
End

Office-1#sh run
Building configuration…

Current configuration : 862 bytes
!
version 15.1
no service timestamps log datetime msec
no service timestamps debug datetime msec
no service password-encryption
!
hostname Office-1
!
ip cef
no ipv6 cef
!
license udi pid CISCO1941/K9 sn FTX15249LBC
!
spanning-tree mode pvst
!
interface GigabitEthernet0/0
no ip address
duplex auto
speed auto
shutdown
!
interface GigabitEthernet0/1
ip address 192.168.1.1 255.255.255.0
duplex auto
speed auto
!
interface Serial0/0/0
ip address 192.168.0.2 255.255.255.252
!
interface Serial0/0/1
no ip address
clock rate 2000000
shutdown
!
interface Vlan1
no ip address
shutdown
!
router eigrp 1
passive-interface GigabitEthernet0/1
network 192.168.1.0
network 192.168.0.0 0.0.0.3
!
ip classless
!
ip flow-export version 9
!
line con 0
!
line aux 0
!
line vty 0 4
login
!
End

Office-2#sh run
Building configuration…

Current configuration : 1427 bytes
!
version 15.1
service timestamps log datetime msec
no service timestamps debug datetime msec
no service password-encryption
!
hostname Office-2
!
ip cef
no ipv6 cef
!
username HQ password 0 PTSAchap
!
license udi pid CISCO1941/K9 sn FTX152467DZ
!
spanning-tree mode pvst
!
interface Tunnel0
ip address 10.10.10.1 255.255.255.252
mtu 1476
tunnel source Serial0/0/0
tunnel destination 10.10.2.2
!
!
interface GigabitEthernet0/0
no ip address
duplex auto
speed auto
shutdown
!
interface GigabitEthernet0/1
ip address 10.10.1.1 255.255.255.0
duplex auto
speed auto
!
interface Serial0/0/0
bandwidth 64
ip address 10.10.2.1 255.255.255.252
encapsulation frame-relay
frame-relay map ip 10.10.2.2 102 broadcast
clock rate 2000000
shutdown
!
interface Serial0/0/1
ip address 10.10.0.2 255.255.255.252
encapsulation ppp
ppp authentication chap
!
interface Vlan1
no ip address
shutdown
!
router eigrp 1
passive-interface GigabitEthernet0/1
network 10.10.1.0 0.0.0.255
network 10.10.2.0 0.0.0.3
network 10.10.0.0 0.0.0.3
network 10.10.10.0 0.0.0.3
!
router ospf 1
log-adjacency-changes
network 10.10.10.0 0.0.0.3 area 0
!
ip classless
!
ip flow-export version 9
!
snmp-server community CiscoPTSA RO
!
logging trap debugging
logging 10.10.1.2
line con 0
!
line aux 0
!
line vty 0 4
login
!
!
ntp trusted-key 15
ntp server 10.10.1.2 key 15
!
End

Branch_12#sh run
Building configuration…

Current configuration : 1210 bytes
!
version 15.1
no service timestamps log datetime msec
no service timestamps debug datetime msec
no service password-encryption
!
hostname Branch_12
!
ip cef
no ipv6 cef
!
license udi pid CISCO1941/K9 sn FTX15243JQ2
!
spanning-tree mode pvst
!
interface Tunnel0
ip address 10.10.10.2 255.255.255.252
mtu 1476
tunnel source Serial0/0/0
tunnel destination 10.10.2.1
!
!
interface GigabitEthernet0/0
ip address 10.10.3.1 255.255.255.0
duplex auto
speed auto
!
interface GigabitEthernet0/1
no ip address
duplex auto
speed auto
shutdown
!
interface Serial0/0/0
bandwidth 64
ip address 10.10.2.2 255.255.255.252
encapsulation frame-relay
frame-relay map ip 10.10.2.1 201 broadcast
clock rate 2000000
shutdown
!
interface Serial0/0/1
no ip address
clock rate 2000000
shutdown
!
interface Vlan1
no ip address
shutdown
!
router eigrp 1
passive-interface GigabitEthernet0/0
network 10.10.3.0 0.0.0.255
network 10.10.2.0 0.0.0.3
network 10.10.10.0 0.0.0.3
!
router ospf 1
log-adjacency-changes
network 10.10.10.0 0.0.0.3 area 0
!
ip classless
!
ip flow-export version 9
!
line con 0
!
line aux 0
!
line vty 0 4
login
!
end

14 diciembre, 2016
Daryl

100% just copy and past to the appropriate routers.

R3########East###########################
en
config t
hostname East
ntp server 10.10.1.2 key 15
snmp-server community CiscoPTSA RO
logging trap debugging
logging 10.10.1.2
service timestamps log datetime msec
router eigrp 1
passive-interface GigabitEthernet0/1
network 10.10.0.0 0.0.0.3
network 10.10.2.0 0.0.0.3
network 10.10.1.0 0.0.0.255
no auto-summary
interface Tunnel0
no shutdown
ip address 10.10.10.1 255.255.255.252
tunnel source s0/0/0
tunnel destination 10.10.2.2
int s0/0/0
no shut
encapsulation frame-relay
ip add 10.10.2.1 255.255.255.252
username R2 password PTSAchap
int s0/0/1
no shut
encapsulation ppp
ppp authentication chap
ip add 10.10.0.2 255.255.255.252

East-Branch1####################
en
config t
hostname East-Branch1
router eigrp 1
passive-interface GigabitEthernet0/0
no auto-summary
network 10.10.2.0 0.0.0.3
network 10.10.10.0 0.0.0.3
network 10.10.3.0 0.0.0.255
interface Tunnel0
no shutdown
ip add 10.10.10.2 255.255.255.252
tunnel source s0/0/0
tunnel destination 10.10.2.1
int s0/0/0
ip add 10.10.2.2 255.255.255.252
encapsulation frame-relay
no shut

R2#############Central###################
en
config t
hostname Central
router eigrp 1
passive-interface GigabitEthernet0/0
no auto-summary
network 192.168.0.0 0.0.0.3
network 172.16.0.0 0.0.0.3
network 10.10.0.0 0.0.0.3
redistribute static
username R3 password PTSAchap
int s0/0/1
no shut
clock rate 128000
ip add 10.10.0.1 255.255.255.252
encapsulation ppp
ppp authentication chap
ip nat inside
ip nat pool DYNAMIC 203.0.113.3 203.0.113.10 netmask 255.255.255.240
ip nat inside source list 1 pool DYNAMIC
ip nat inside source list 2 interface Serial0/1/0 overload
ip access-list standard 2
permit 10.10.1.0 0.0.0.255
permit 10.10.3.0 0.0.0.255
ip access-list standard 1
permit 192.168.1.0 0.0.0.255
int s0/0/0
no shut
clock rate 128000
ip add 192.168.0.2 255.255.255.252
encapsulation hdlc
ip nat inside
ip route 0.0.0.0 0.0.0.0 s0/1/0
ip nat inside source static 172.16.0.2 203.0.113.14
int g0/0
ip nat inside
int s0/1/0
ip nat outside
router eigrp 1
passive-interface GigabitEthernet0/1
no auto-summary
network 192.168.0.0 0.0.0.3
network 192.168.1.0 0.0.0.255
int s0/0/0
no shut
ip add 192.168.0.1 255.255.255.252
encapsulation hdlc

R1###########West######################
en
config t
hostname West
router eigrp 1
passive-interface GigabitEthernet0/1
no auto-summary
network 192.168.0.0 0.0.0.3
network 192.168.1.0 0.0.0.255
int s0/0/0
no shut
ip add 192.168.0.1 255.255.255.252
encapsulation hdlc?

3 diciembre, 2015

Resumen de la privacidad

Este sitio web utiliza cookies para mejorar su experiencia mientras navega por el sitio web. De ellas, las cookies clasificadas como necesarias se almacenan en su navegador, ya que son esenciales para el funcionamiento de las funciones básicas del sitio web. También utilizamos cookies de terceros que nos ayudan a analizar y comprender cómo utiliza usted este sitio web. Estas cookies se almacenan en su navegador sólo con su consentimiento. También tiene la opción de excluirse de estas cookies. Pero la exclusión de algunas de estas cookies puede afectar a su experiencia de navegación.

Necesarias

Siempre activado

Las cookies necesarias son absolutamente imprescindibles para que el sitio web funcione correctamente. Estas cookies garantizan las funcionalidades básicas y las características de seguridad del sitio web, de forma anónima.

Cookie	Duración	Descripción
cookielawinfo-checbox-analytics	11 months	Esta cookie es establecida por el plugin GDPR Cookie Consent. La cookie se utiliza para almacenar el consentimiento del usuario para las cookies de la categoría "Analytics".
cookielawinfo-checbox-functional	11 months	La cookie se establece por el consentimiento de cookies GDPR para registrar el consentimiento del usuario para las cookies en la categoría "Funcional".
cookielawinfo-checbox-others	11 months	Esta cookie es establecida por el plugin GDPR Cookie Consent. La cookie se utiliza para almacenar el consentimiento del usuario para las cookies de la categoría "Otros".
cookielawinfo-checkbox-necessary	11 months	Esta cookie es establecida por el plugin GDPR Cookie Consent. Las cookies se utilizan para almacenar el consentimiento del usuario para las cookies en la categoría "Necesario".
cookielawinfo-checkbox-performance	11 months	Esta cookie es establecida por el plugin GDPR Cookie Consent. La cookie se utiliza para almacenar el consentimiento del usuario para las cookies de la categoría "Rendimiento".
viewed_cookie_policy	11 months	La cookie es establecida por el plugin GDPR Cookie Consent y se utiliza para almacenar si el usuario ha consentido o no el uso de cookies. No almacena ningún dato personal.

Related Articles

About The Author

CisacadESP

2 Comments

Edinson Acevedo

Daryl

Leave a Reply Cancel Reply